Chemical Circulating Pump with Variable Speed Controlled

Brief introduction
YL Chemical circulating pump is to be found in numerous processes, where their reliable low shear flow characteristics are ideally suited to the transfer of media such as chemical additives/agents, resins, oils products. We select the pump according to your characteristics of medium and condition of the technological requirements, bring you the best pump for your critical process, satisfied by you and your customers. 

Pump Applications
Petrochemicals: Thick oil, heavy oil, crude oil, bitumen, grease, lub oil, catalytic agent and other viscous liquids.
Fine Chemicals: Dyes stuffs, pigments, hemical additives, adhesives, silicone oil, leather oil, a variety of colloidal materials and pulp, Paint, dope, printing ink, insulating paint, resin, additives and assistants, organic solvent, etc.
Chemical fibers: Pectic slurry, PVA, spandex slurry, vinylon slurry, Acrylic slurry, polyester slice, terylence, polypropylene fiber, rayon, functional fiber etc.

Pump Working principle

The even rotation of the rotor pair creates a vacuum on the priming side of the pump, which can be defined by the direction of rotation of the drive. This vacuum draws the liquid into the pump chamber. With further rotation, the pumped medium is conveyed past the pump wall into the pressure area. Up to six chamber charges are displaced with each drive rotation depending on the rotor type. When the rotor is at a standstill, the pump seals off almost completely.

Pump Structure

Complete pump consists of bare shaft pump, coupling& shield, gear reduer with motor and baseplate. You can only have our bare shaft pump.

Pump Specifications

Note*

1. Tested medium: water. Your liquid's density, viscosity and temperature are necessary to supply when choose the pump.

2. Speed, flow rate, electrical power and pressure will be varified according to different liquid properties.

3. Port size can be changed as needed.

4. YL reserves the right to change specifications without prior notification.

How to choose our pump
Dear Customer,
To ensure satisfactory performance of required pumps, it is important that the pump must be properly selected. Below table is for your selection guideline, which is nessary to supply us for a targeted solution and offer. 

Factory workshop showing




Contact Us








 

Brief introduction
YL Chemical circulating pump is to be found in numerous processes, where their reliable low shear flow characteristics are ideally suited to the transfer of media such as chemical additives/agents, resins, oils products. We select the pump according to your characteristics of medium and condition of the technological requirements, bring you the best pump for your critical process, satisfied by you and your customers. 

Pump Applications
Petrochemicals: Thick oil, heavy oil, crude oil, bitumen, grease, lub oil, catalytic agent and other viscous liquids.
Fine Chemicals: Dyes stuffs, pigments, hemical additives, adhesives, silicone oil, leather oil, a variety of colloidal materials and pulp, Paint, dope, printing ink, insulating paint, resin, additives and assistants, organic solvent, etc.
Chemical fibers: Pectic slurry, PVA, spandex slurry, vinylon slurry, Acrylic slurry, polyester slice, terylence, polypropylene fiber, rayon, functional fiber etc.

Pump Working principle

The even rotation of the rotor pair creates a vacuum on the priming side of the pump, which can be defined by the direction of rotation of the drive. This vacuum draws the liquid into the pump chamber. With further rotation, the pumped medium is conveyed past the pump wall into the pressure area. Up to six chamber charges are displaced with each drive rotation depending on the rotor type. When the rotor is at a standstill, the pump seals off almost completely.

Pump Structure

Complete pump consists of bare shaft pump, coupling& shield, gear reduer with motor and baseplate. You can only have our bare shaft pump.

Pump Specifications

Note*

1. Tested medium: water. Your liquid's density, viscosity and temperature are necessary to supply when choose the pump.

2. Speed, flow rate, electrical power and pressure will be varified according to different liquid properties.

3. Port size can be changed as needed.

4. YL reserves the right to change specifications without prior notification.

How to choose our pump
Dear Customer,
To ensure satisfactory performance of required pumps, it is important that the pump must be properly selected. Below table is for your selection guideline, which is nessary to supply us for a targeted solution and offer. 

Factory workshop showing




Contact Us








 

Zamak die casting parts

Zamak Die Casting Gear,Die Castings,Die Casting Molding

Guantong Plastic Mould Co., Ltd. , http://www.zhymould.com